Get the app (opens the App Store in a new tab)

Help

Plates per side in LiftLoggr: set your bar and plates

LiftLoggr shows the plates per side under every barbell set. Set your bar (20, 15, 10 kg or none) and the plates your gym has in Settings → Bar & plates.

Key takeaways

  1. 01Every barbell set shows a line like 25 · 15 per side.
  2. 02Settings → Units & totals → Bar & plates: pick the bar, tick the plates you have.
  3. 03The same settings drive warm-ups, drop sets and progression steps.
  4. 04A weight you can't load reads Closest … per side.
On this page

LiftLoggr works out the plates for you: under every barbell set it shows what to load on each side, for example 25 · 15 per side for 100 kg on a 20 kg bar. Tell it your bar and the plates your gym has in Settings → Units & totals → Bar & plates.

Checked against LiftLoggr 1.5.2 for iPhone.

Read the plate line

  1. Start a workout with a barbell exercise.
  2. Under the set’s weight, a muted line lists the plates for one side, heaviest first: 25 · 15 per side.
  3. At exactly the bar’s weight it reads Bar only.
  4. If the weight can’t be made with your plates, it shows the nearest loadable total. Type 101.5 kg and it reads Closest 102.5 kg: 25 · 15 · 1.25 per side.
  5. Tap the plate line to open Bar & plates and change your setup without leaving the workout.

The line updates as you type a new weight.

Set your bar and plates

  1. Tap the Settings tab.
  2. Under Units & totals, tap Bar & plates.
  3. Under Bar, pick one: 20 kg, 15 kg, 10 kg or No bar.
  4. Under Plates, tick every plate your gym has. The last plate can’t be unticked.
  5. Changes save right away. Reset to defaults puts the defaults back.
Units Bars Plates offered Ticked by default
kg 20, 15, 10, none 25, 20, 15, 10, 5, 2.5, 1.25, 0.5 All except 0.5
lb 45, 35, 25, none 45, 35, 25, 10, 5, 2.5, 1.25 All except 1.25

Switch units under Units & totals (kg / lb). The bar maps to its counterpart (20 kg ↔ 45 lb, 15 ↔ 35, 10 ↔ 25).

What else uses these settings

The footer says it: “Used for plate math, warm-ups and progression steps.”

  • Warm-up sets round to loads you can build. See add warm-up sets.
  • Drop sets start at about 80 % of the weight, rounded down to a loadable total. See log a drop set.
  • Double progression adds twice your smallest plate to a barbell lift when you top the rep range: 2.5 kg with the default plates.

Examples on a 20 kg bar, default kg plates

Total Per side
60 kg 20
82.5 kg 25 · 5 · 1.25
100 kg 25 · 15
140 kg 25 · 25 · 10
21 kg Bar only (closest)

Training on a 15 kg or 10 kg bar? Pick it under Bar and every plate line, warm-up and drop set follows. Bar weights explained: how much does a barbell weigh. Need numbers without the app? Use the plate calculator.

Questions

Why don't I see plates under a set?

The plate line only shows for barbell exercises with a weight above zero and at least the bar's weight. Dumbbell, machine and cable exercises don't get one.

My gym has no 1.25 kg plates. What changes?

Untick 1.25 kg in Bar & plates. Plate lines, warm-ups and drop sets then only use what you have, and double progression steps up by twice the smallest plate left, 5 kg instead of 2.5 kg.

Does it work in pounds?

Yes. With lb selected, the bars are 45, 35, 25 lb or none, and the plates are 45, 35, 25, 10, 5, 2.5 and 1.25 lb.

0